Jump to content


Walter Klassen Vest

  • Please log in to reply
5 replies to this topic

#1 SimonChamp



  • Members
  • PipPip
  • 13 posts

Posted 30 March 2015 - 04:24 PM

I was at a workshop and saw someone with a vest made by Walter Klassen... tried it out and it felt quite nice. Anyone had any floors with it? not a bad price too

  • 0

#2 Brad Hruboska

Brad Hruboska

    Advanced Member

  • Sustaining Members
  • 157 posts
  • Toronto

Posted 01 April 2015 - 11:27 AM

I was an early adopter. #48 I think. originally built in 2001. Service is fantastic. The Klassen parts have held up extremely well, and the harness adapts well to EZ rig with several after market adapters, Klassen makes one and Lentequip markets another that is a bit faster to change back and forth. I use the air bladder system, which allows for adjusting fit , but have found that once i finds the setting i like i leave it. The original bladder lasted for 10 years. the ratchet straps and buckles do sometimes need replacing, but i can do that in under 4 minutes ( three if the AD is looking at his watch). The ratcheting strap system does eventually wear, and i keep a good stock of strips . If they look worn i just change then out. Again, easy two minute job. Klassen always gives you spares of buckles and straps when you buy new.

I will say this. I do use an aftermarket  MK-5 male PRO socket block, which is solid steel, with a double thickness shoulder piece. Klassen also makes a solid PRO arm adapter . I have both sheared a titanium male block, and blown out the tie rod ball ends. The ball rod ends are not at all necessary with the Klassen harness as the tilt angle is adjusted by a knob integral to the rear Klassen arm. The same is true for the Klassen Hard mount adapter. Most of my local colleagues have made this adaptation too to continue with the Klassen rear mount harness, which is still the most comfortable thing I've used.  It is a bit wider getting through doorways, small corridors like airplanes etc, but for live work, its awesome.

All of this equipment is intended for professional use and it is assumed that as a steadicam professional you have a basic understanding of basic care and mechanical maintenance. I like the fact that some manufacturers are posting Videos online to demystify this process.

  • 0

#3 Stewart Smith

Stewart Smith


  • Sustaining Members
  • 14 posts
  • Detroit, Michigan

Posted 02 April 2015 - 11:18 PM

I also use and love the Klassen harness. However Pro will say that using the MK-V socket block adapter with the Pro arm will void the warranty as the rod ends are the first line of defense in the eventual event of a failure, replace it with a solid block and the next thing to go will be a lot less pretty and more expensive to replace than the rod ends. It's been discussed here before, so I think it's worth mentioning.
  • 0

#4 Jason Ippolito

Jason Ippolito

    New Member

  • Members
  • Pip
  • 2 posts
  • South Pasadena, CA

Posted 25 April 2015 - 10:13 AM

Can you clarify what the "rod ends" are? The left/right threads on the WK block? Something else? Thanks.
  • 0

#5 Jarrett P. Morgan

Jarrett P. Morgan

    Advanced Member

  • Sustaining Members
  • 229 posts
  • Los Angeles, CA

Posted 25 April 2015 - 11:55 AM

Can you clarify what the "rod ends" are? The left/right threads on the WK block? Something else? Thanks.

The rod ends are the pieces in the arm that allow for side to side adjustment on the front mounted vest. Accessed via an allen key into the socket block.


The WK vest (and all back mounted vests that I know of) change the forces on the socket block by 90 degrees, thus putting forces onto the rod ends that they were not particularly designed to take. 

  • 0

#6 G. Grammatikos

G. Grammatikos

    Advanced Member

  • Members
  • PipPipPip
  • 98 posts
  • Greece

Posted 27 April 2015 - 09:26 PM

I work over 10 years wk &pro arm with no problem ( I have ended and I tight once a year the socket block )
I had forget working with front mounted vest !!!!
  • 0

GPI Pro Systems

Paralinx LLC

PLC Electronics Solutions

Boland Communications

Wireless Video Systems

The Moses Pole - Steadicam Monopod

rebotnix Technologies

Engineered Cinema Solutions

Media Blackout - Custom Cables and AKS

Varizoom Follow Focus


Omnishot Systems

PLC - Bartech

Ritter Battery

Betz Tools for Stabilizers