Hi folks, Figured I'd put a bunch of stuff on here for sale instead of individual ads...
PRO GEN 3 HD Cinema HD Top and Bottom Electronics with Tally Option, Record out Lemo voltage is regulated 12V not 5V This will allow you to power your Atomos, Nano, Pix240, etc.. at the bottom of your sled.
$4400 without the top Tally sensor, and bottom Tally LED cable
$4600 with the Tally cables
BOXX Cobalt system, ( SD, or component Video Tx and Rx)
Boxx Transmitter ( 5Ghz and 2.8Ghz switchable) with AB mounts both sides. It can be powered from a Batt when sandwiched between the batt and camera? or you can power it via the 4 pin Hirose on the Tx via one of the power cables included which are:
Hirose 4 pin to PRO- Vid/Pwr 4 pin
Hirose 4 pin to Hirose 4 pin ( like on the rear of most Broadcast cameras)
Hirose 4 pin to XLR4Male
Hirose 4 pin to P Tap
3 palet style antennas
The system also transmits audio although I never used this option.
Comes with mini xlr 5 pin to standard XLR5Female ( for the audio out of some broadcast video cams
also mini xlr 5 pin to standard headphone male jack
Boxx receiver 5Ghz and 2.8Ghz switchable with 2 antennas
AC Power supply 100V - 240V input 12 V output
Power cable for AC power supply
Breakout Multi Pin cable loom with component connectors, Audio left and right connectors and 4 pin XLR connector.
( I've never used the Multi Pin loom)
The receiver can be powered via the AC power supply, or the Hirose 4 pin connector on the unit. you can use one of the above Hirose connectors to power the receiver and another or AB brick to power the Transmitter.
I had Nebtek install a male side AB plate to one side of the receiver so you can attach it to the back of a monitor, etc.. but it is only there to mount it, not connected internally, I would guess you can install a receiver plate on the opposite side and have it wired like the transmitter so you could attach it behind a monitor and then add a Batt to it and power both, but that would be up to you.
The receiver is powered thru it's 4 pin Hirose like the Tx unit.
Price $950 shipped Priority via USPS to anywhere in the continental US.
Outside of the US, Shipping is not included.
Marshall 7" Monitor HD/SDI with Anton Bauer back
I installed a Transvideo mounting bracket underneath so you can use it with the many monitor brackets out there that have spigots. Great shape, works great!. I only use this monitor indoors on studio live shows, so that's most of the life it's seen. It's not a Daylight bright model, but with a makeshift lens hood I've done well outside with it.
Model #V-R70P-HDSDI with the Anton Bauer back and the Transvideo mounting bracket. $799 shipped in the continental US.
XCS 2" CF Carbon Fibre Super Post with 8 pin Lemo SD PRO cable and PRO/GPI threaded ends.
Comes in rigid canvas covered slip tube/case.
$2400 includes shipping anywhere in the US.
Pictured here with the Pro Lite lower stage and the Top stage and DB on it,
None of those things are included. Only the Super post, cable, and shipping tube. No Docking Bracket, etc..
ZOE ZOOM Riser
Works with ZOE eng zoom controls, the ENG-12 and ENG-8.
When attaching it to my gimbal (XCS)I didn't want it to gouge the cover on the gimbal handle.
I had one of these made to solve that problem. Used it for almost a year and then decided to have more made and have them anodized.
Black Anodized Aluminum. Also helps stiffen the two threaded rods of the Zoe zoom controls. Makes for a nice snug fit.
I use it on the XCS gimbal with the neoprene like sleeve. If your gimbal handle isn't as thick you may try wraping something around the area where this will rest.
This tray slides onto either a panasonic or Sony broadcast cameras' viewfinder dovetail after removing the finder. You can drill the base plate and screw down a Monitor, or velcro a transmitter/receiver to it ( terradek, canatrans, modulus, paralinx, etc..) lots of possibilities. $150 shipped. in the US
Kino Flo Power Supply with 4- pin XLR connector. It operates with 120-230 AC Voltage, and draws 6.5 amps. As equipped, it converts 120V AC power to 12V DC power to operate the Kino Flo 12V ballast (#BAL-140X) using available AC power sources. One 12V Power Supply will run one 12V ballast, which can operate a single Kino Flo tube, in sizes 15" to 4'. Practically new, Retails at $294, selling for $120 shipped in the US.
Transvideo Adapter slider plate.
This Slider bracketcame with my HD6 monitor, it also fits on the Starlite 4" Monitor, Bolts onto the Transvideo monitors and has a sliding 1/4"-20 Brass insert and locking screw with large Transvideo nut.
BFD Run cable 11 pin fisher connector 26" Long
Sony XC-57 B&W SD box Camera with PRO 4 pin Lemo Vid/Pwr cable
Using this cable would power the unit, and feed it SD video from your sled.
Uses C Mount lenses. great to place in a weight cage and practice your moves.
$120 shipped ( Cable costs that )
NOS ( New old stock) Bolex Rubber Eyecup
One is a bit dirty from being moved around for years. If you have a Bolex without a finder, you NEED this!!. $20 each shipped.
Vintage Arriflex camera Lapel/Tie pins
Brought these back from the factory in Munchen many many years ago. Will certainly start up a conversation ...(or stares..) at the next dress up function... ( SOC Lifetime achievement awards) $20 each shipped, take your pic)
2013-03-26 18.05.56.jpg 51.69KB 95 downloads
arri pins (4).jpg 104.73KB 102 downloads
2013-03-26 18.06.09.jpg 63.55KB 115 downloads
arri pins (3).jpg 63.2KB 133 downloads
20130816_153851.jpg 64.39KB 109 downloads
20130816_153908.jpg 76.16KB 90 downloads